>DsmbISP< Kunci Jawaban Cisco CCNA Discovery 2 Chapter 5

1. In what two ways does SDM differ from the IOS CLI? (Choose two.)
SDM is used for in-band management only. The IOS CLI can be used for in-band and out-of-band management.
SDM is accessed through a Telnet application. The IOS CLI is accessed through a web browser.
SDM is available for all router platforms. The IOS CLI is available for a limited number of Cisco devices.
SDM utilizes GUI buttons and text boxes. The IOS CLI requires the use of text-based commands.
SDM is used for advanced configuration tasks. The IOS CLI is preferred for initial basic device configuration.

2. Which mode will a configured router display at login?
global configuration mode
setup mode
ROM monitor mode
user EXEC mode

3. Refer to the exhibit. Which password or passwords will be encrypted as a result of the configuration that is shown?
virtual terminal only
enable mode only
console and virtual terminal only
enable mode and virtual terminal
only the service password
all configured passwords

4. Refer to the exhibit. Which three sets of commands are required to enable administrators to connect to the Switch1 console over Telnet for configuration and management? (Choose three.)
Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.2.64 255.255.255.192

Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.2.66 255.255.255.192

Switch1(config)# interface vlan 1
Switch1(config-if)# ip address 192.168.2.126 255.255.255.192
Switch1(config-if)# no shutdown

Switch1(config)# line vty 0 4
Switch1(config-line)# enable password cisco
Switch1(config-line)# login

Switch1(config)# line vty 0 15
Switch1(config-line)# password cisco
Switch1(config-line)# login

Switch1(config)# ip default-gateway 192.168.2.65

5. How does the SYST LED on the catalyst 2960 switch indicate a POST failure?
blinks rapidly amber
blinks rapidly green
steady amber
steady green

6. Refer to the exhibit. A company always uses the last valid IP address in a subnetwork as the IP address of the router LAN interface. A network administrator is using a laptop to configure switch X with a default gateway. Assuming that the switch IP address is 192.168.5.147/24, what command will the administrator use to assign a default gateway to the switch?
X(config)# ip default-gateway 192.168.5.254
X(config)# ip gateway 192.168.5.1
X(config)# ip route 0.0.0.0 0.0.0.0 192.168.5.1
X(config)# ip default-route 192.168.5.1
X(config)# ip route 192.168.5.254 255.255.255.0 fastethernet 0/0

7. A technician has made changes to the configuration of a router. What command will allow the technician to view the current configuration before he saves the changes?
router# show running-config
router# show startup-config
router# show flash
router# show version

8. Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)
VTY interface
console interface
Ethernet interface
secret EXEC mode
privileged EXEC mode
router configuration mode

9. To save time, IOS commands may be partially entered and then completed by typing which key or key combination?
Tab
Ctrl-P
Ctrl-N
Up Arrow
Right Arrow
Down Arrow

10. What is the correct command sequence to configure a router host name to ‘LAB_A’?
Router> enable
Router# configure terminal
Router(config)# hostname LAB_A

Router> enable
Router# hostname LAB_A

Router> enable
Router# configure router
Router(config)# hostname LAB_A

Router> enable
Router(config)# host name LAB_A

11. Refer to the exhibit. From the router console, an administrator is unable to ping a Catalyst switch that is located in another building. What can the administrator do from her location to check the IP configuration of the attached switch?
Open an SDM session with the switch from her desktop.
Telnet to the switch from the router console.
Use the show cdp neighbors detail command from the router console.
The administrator must go to the switch location and make a console connection to check these settings.

12. Which two options must be selected in SDM Express to enable a router serial interface to obtain an IP address automatically? (Choose two.)
Easy IP (IP negotiated)
IP unnumbered
No IP address
HDLC encapsulation
Frame Relay encapsulation
PPP encapsulation

13. What three settings can be made in the SDM Express basic configuration screen? (Choose three.)
host name
DHCP options
domain name
interface IP addresses
enable secret password
DNS server IP addresses

14. Which tasks can be accomplished by using the command history feature? (Choose two.)
View a list of commands entered in a previous session.
Recall up to 15 command lines by default.
Set the command history buffer size.
Recall previously entered commands.
Save command lines in a log file for future reference.

15. What option within Cisco SDM Express must be configured to allow hosts that receive IP address settings from the router to resolve names on the network or Internet?
host name
domain name
DHCP address pool
DNS server IP address

16. Which three encapsulation types can be set on a serial interface by an administrator who is using SDM Express? (Choose three.)
ATM
CHAP
Frame Relay
HDLC
PAP
PPP

17. Which command will display routing table information about all known networks and subnetworks?
Router# show ip interfaces
Router# show ip connections
Router# show ip route
Router# show ip networks

18. A network administrator needs to configure a router. Which of the following connection methods requires network functionality to be accessible?
console
AUX
Telnet
modem

19. Which three pieces of information about a neighbor device can be obtained by the show cdp neighbors command? (Choose three.)
platform
routing protocol
connected interface of neighbor device
device ID
IP addresses of all interfaces
enable mode password

20. Which function is a unique responsibility of the DCE devices shown in the exhibit?
transmission of data
reception of data
clocking for the synchronous link
noise cancellation in transmitted data

21. Which of the following are functions of NVRAM? (Choose two.)
stores the routing table
retains contents when power is removed
stores the startup configuration file
contains the running configuration file
stores the ARP table

22. Refer to the exhibit. Which series of commands will enable users who are attached to Router1 to access the remote server?
Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.129 255.255.255.252
Router1(config-if)# clock rate 64000
Router1(config-if)# no shutdown

Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.125 255.255.255.252
Router1(config-if)# no shutdown

Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.125 255.255.255.252
Router1(config-if)# clock rate 64000
Router1(config-if)# no shutdown

Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.129 255.255.255.252
Router1(config-if)# no shutdown

23. A network technician is attempting to add an older workstation to a Cisco switched LAN. The technician has manually configured the workstation to full-duplex mode in order to enhance the network performance of the workstation. However, when the device is attached to the network, performance degrades and excess collision are detected. What is the cause of this problem?
The host is configured in a different subnet from the subnet of the switch.
There is a duplex mismatch between the workstation and switch port.
The switch port is running at a different speed from the speed of the workstation NIC.
The host has been configured with a default gateway that is different from that of the switch.

24. Which of the following statements are true regarding the user EXEC mode? (Choose two.)
All router commands are available.
Global configuration mode can be accessed by entering the enable command.
A password can be entered to allow access to other modes.
Interfaces and routing protocols can be configured.
Only some aspects of the router configuration can be viewed.

25. Which command turns on a router interface?
Router(config-if)# enable
Router(config-if)# no down
Router(config-if)# s0 active
Router(config-if)# interface up
Router(config-if)# no shutdown

26. A router has a valid operating system and a configuration stored in NVRAM. When the router boots up, which mode will display?
global configuration mode
setup mode
ROM monitor mode
user EXEC mode

27. Which two statements are true about the NVRAM on a Cisco device?(Choose two.)
stores the routing table
retains contents when power is removed
stores the startup configuration file
contains the running configuration file
stores the ARP table

28. An administrator enters the show ip route command into a router. What type of information will be displayed?
the current configuration stored in RAM
the networks learned from other neighbors
the encapsulation and bandwidth of every interface
the private IP addresses translated to public IP addresses

29. When utilizing SDM Express, which two configuration options allow a router serial interface to obtain an IP address without manually configuring it? (Choose two.)
Static IP Address
Frame Relay encapsulation
IP Negotiated
HDLC encapsulation
IP Unnumbered

30. Refer to the exhibit. Based on the output of the show port-security interface fastethernet0/1
command on the switch, which statement about the switch port is true?
The port has been shut down.
Only three unique MAC addresses are permitted to use this port.
There are ten devices with different MAC addresses connected to this port.
Port security has been violated seven times on this port.

31. Refer to the exhibit. Users on both SW1 and SW2 report that they are unable to communicate with each other. A network administrator issues show ip interface brief commands on both routers to troubleshoot the connectivity between the two networks. What action will correct the connectivity issue?
Configure a default route on router RA pointing to router RB.
Modify the network address of the serial link from a /30 to a /24.
Issue a clock rate command on the s0/0/0 interface on router RA.
Issue a no shutdown command on the s0/0/0 interface on router RB.
Issue a debug ip rip on both routers to verify that the routing protocol is functioningproperly.

32. Refer to the exhibit. A company always uses the last valid IP address in a subnetwork as the IP address of the router LAN interface. A network administrator is using a laptop to configure switch X with a default gateway via the switch console port. The switch VLAN 1 interface is assigned IP address 192.168.5.68/26. What command will the administrator use to assign a default gateway to the switch?
X(config)# ip default-gateway 192.168.5.1
X(config)# ip default-gateway 192.168.5.126
X(config)# ip default-gateway 192.168.5.190
X(config)# ip route 0.0.0.0 0.0.0.0 192.168.5.192
X(config)# ip route 192.168.5.0 255.255.255.192 192.168.5.1

33. What step must be completed before port security can be enabled on an interface?
The interface must be shut down.
The interface must be in access mode.
The maximum number of MAC addresses must be configured.
The violation mode must be configured.

34. Which of the following identifies the correct items needed to initially configure a router?
1) DB-9-to-RJ-45 on the PC’s serial port
2) a straight through cable
3) the router’s console port

1) PC’s Ethernet port
2) a crossover cable
3) the router’s Ethernet port

1) DB-9-to-RJ-45 on the PC’s serial port
2) a rollover cable
3) the router’s Ethernet port

1) PC’s Ethernet port
2) a rollover cable
3) the router’s console port

1) DB-9-to-RJ-45 on the PC’s serial port
2) a rollover cable
3) the router’s console port

1) PC’s Ethernet port
2) a rollover cable
3) the router’s Ethernet port